OSELLA FA1 WIP by Formula Kits!
-
Topic author - F2 Champion
- Posts: 94
- Joined: Sun Sep 20, 2009 10:59 am
- Favorite F1 Team or Driver: Senna, Piquet, Pryce, Osella, Lotus, Copersucar, Tyrrell, Minardi, RAM
- Status: Offline
Re: OSELLA FA1 WIP by Formula Kits!
Valeu pela força Teles!
Jacques, with the main body and the bottom ready now I think that 60 - 70% of the job is concluded. My next task is start to draw the PE´s and decals, very easy task, but here I´ll need some funds to carry on with the project I´ll do, be sure. Most of you can think this project is very delayed, but I always read some topics where some people complain about the low or very bad quality of some garage kits... I don´t want that my kit be one of them, I want to perform the best I can and this search for perfection takes a extra time, that´s it. Thank you all for your attention!
Jacques, with the main body and the bottom ready now I think that 60 - 70% of the job is concluded. My next task is start to draw the PE´s and decals, very easy task, but here I´ll need some funds to carry on with the project I´ll do, be sure. Most of you can think this project is very delayed, but I always read some topics where some people complain about the low or very bad quality of some garage kits... I don´t want that my kit be one of them, I want to perform the best I can and this search for perfection takes a extra time, that´s it. Thank you all for your attention!
-
Topic author - F2 Champion
- Posts: 94
- Joined: Sun Sep 20, 2009 10:59 am
- Favorite F1 Team or Driver: Senna, Piquet, Pryce, Osella, Lotus, Copersucar, Tyrrell, Minardi, RAM
- Status: Offline
-
- F2 Champion
- Posts: 186
- Joined: Fri Oct 29, 2010 6:43 am
- Your Name: João Alfredo
- Favorite F1 Team or Driver: José Carlos Pace, Roberto Pupo Moreno.
- Location: Brazil
- Contact:
- Status: Offline
Re: OSELLA FA1 WIP by Formula Kits!
Belo trabalho Rodrigo!.
Espero que continue.
Abraço,
João Alfredo.
Espero que continue.
Abraço,
João Alfredo.
[url]https://sites.google.com/view/racingkits/home[/url]
-
- Major Constructor
- Posts: 1018
- Joined: Fri Aug 01, 2008 10:05 pm
- Favorite F1 Team or Driver: Ferrari, Alfa Romeo
- Location: Switzerland
- Status: Offline
Re: OSELLA FA1 WIP by Formula Kits!
Very nice.
I think you can reduce your layer hight further though.
Unless this is just a test print for speed?
I think you can reduce your layer hight further though.
Unless this is just a test print for speed?
Currently building:
Alfa Romeo 159 (since 2021)
Recently finished:
Renault R30 (since 2010)
Alfa Romeo 159 (since 2021)
Recently finished:
Renault R30 (since 2010)
-
Topic author - F2 Champion
- Posts: 94
- Joined: Sun Sep 20, 2009 10:59 am
- Favorite F1 Team or Driver: Senna, Piquet, Pryce, Osella, Lotus, Copersucar, Tyrrell, Minardi, RAM
- Status: Offline
Re: OSELLA FA1 WIP by Formula Kits!
Muito obrigado João, I hope so too!
I'm printing in 0.1mm layers and thinner layers increases too much the printing time. I'm using a FDM printer, it will requires putty and sanding anyway in all surface and the final result has been satisfactory despite the height of layer. For sure you need extra patience, accuracy and very very soft fingers at sanding
-
- Major Constructor
- Posts: 1051
- Joined: Sun Jul 20, 2014 7:28 am
- Favorite F1 Team or Driver: Jim Clark, Lotus
- Status: Offline
Re: OSELLA FA1 WIP by Formula Kits!
Brave man! Running this through an FDM printer. Out of curiousity - may I ask for the printing time and the general setup (printer, nozzle size, ...)? Since I have both an FDM (Ender v3 with 0.2 nozzle I believe) and a resin printer (Anycubic Photon) and can compare the printing times for both (newsflash: resin usually wins by a significant margin). Depending on size, but yours must be through the roof at 0.1mm.
Again, kudos for what you are doing, especially with an FDM printer.
Again, kudos for what you are doing, especially with an FDM printer.
Cheers,
Roman
Roman
-
- Midfield
- Posts: 493
- Joined: Mon Jan 31, 2005 6:36 pm
- Favorite F1 Team or Driver: Copersucar-Fittipaldi
- Location: Canela/RS/Brasil
- Contact:
- Status: Offline
Re: OSELLA FA1 WIP by Formula Kits!
Very nice!!!
To de olho hehehe
To de olho hehehe
-
- Major Constructor
- Posts: 1018
- Joined: Fri Aug 01, 2008 10:05 pm
- Favorite F1 Team or Driver: Ferrari, Alfa Romeo
- Location: Switzerland
- Status: Offline
Re: OSELLA FA1 WIP by Formula Kits!
You should try to print it in vertical.formula.kits wrote: ↑Thu Aug 04, 2022 7:53 pmMuito obrigado João, I hope so too!
I'm printing in 0.1mm layers and thinner layers increases too much the printing time. I'm using a FDM printer, it will requires putty and sanding anyway in all surface and the final result has been satisfactory despite the height of layer. For sure you need extra patience, accuracy and very very soft fingers at sanding
It produces much better results
Currently building:
Alfa Romeo 159 (since 2021)
Recently finished:
Renault R30 (since 2010)
Alfa Romeo 159 (since 2021)
Recently finished:
Renault R30 (since 2010)
-
Topic author - F2 Champion
- Posts: 94
- Joined: Sun Sep 20, 2009 10:59 am
- Favorite F1 Team or Driver: Senna, Piquet, Pryce, Osella, Lotus, Copersucar, Tyrrell, Minardi, RAM
- Status: Offline
Re: OSELLA FA1 WIP by Formula Kits!
Graaaande Teles!
Thx mate. This part took +- 6:30 hours because the settings on Cura looking for better results (slower, less temperature on hotend). The nozzle is a standart 0.4mm of the BQ B1. PLA filament.
I haven't tried this yet, maybe really can be a better way